Dating back half a millennium, the lockback is special and timeless
By Mike Haskew, BLADE® field editor
One of the most popular of folder locking mechanisms, the lockback is proof positive that everything old is new again. Most knife enthusiasts are aware of the influence the lockback has had for what is going on 60 years now, even though its origin goes back much further. Its ease of carry, safety and durability make for a winning knife, and in both the factory and custom segments of the industry, the lockback continues as a staple of production, craftsmanship and sales.
“You can make the lockback strong and heavy duty,” remarked Blade Magazine Cutlery Hall-Of-Fame© member Sal Glesser of Spyderco. “We built a special machine to test and break stuff, and [the lockback] is a very heavy-duty lock at up to 200-inch pounds of strength for every inch of blade. By its geometry, the lockback is capable of as much strength as you build into it.”
Glesser cites a couple of additional reasons for the rise and popularity of the lockback. The lockback spring can be easily positioned so it will not close inadvertently on the user, while the mechanism itself is easy to operate.
“The lockback has evolved over time,” Glesser explained. “The configuration of the locking bar changed in the mid-’70s after Harvey McBurnette showed Al Mar how to do that. Now, there are front, mid and rear lockbacks, and the advantage of the lockback produced by Al Mar is that the kicker of the blade is located where the lock pivot is, so the edge of the blade did not hit the spring. We asked Al for permission to use his lock on our early knives and still use a lock that is essentially the same to this day.”
One concern for the lockback has been the level of engineering required in its construction. “The lockback is an engineering challenge,” Sal concluded, “and shortening the [lock bar for the front- and mid-lockback models] makes it even harder to do. Because it is difficult to make, we have worked as recently as the last two years on refining the lock to virtually eliminate play in the blade.”
Despite or perhaps because of its requirement for tight tolerances, the lockback has a substantial lineage. According to Bill Claussen, co-author of Sheffield Exhibition Knives, the lockback has been around in various forms since 15th-century Spain. Other European cutlers—including the French, Italians and English—have produced lockback variants during the past 500 years or so.
In the modern era, Claussen cites the Buck 110 folding hunter, which hit the market in 1964, as an industry icon. “It changed the face of modern pocketknives,” he commented. “Although lockbacks had been introduced to the U.S. for more than 200 years, they were not made affordable and convenient in mass production until Al Buck introduced his knife. This knife was quickly adopted by sportsmen, tradesmen, truckers and other workmen as an ideal, all-around, heavy-duty work knife. Vintage 110s are hard to find today, and one in mint condition will cost a small fortune if you can find one.”
Chairman of the board at Buck Knives, Cutlery Hall-Of-Famer Chuck Buck recognizes the pivotal role the 110 has played in modern lockback development, and acknowledges the challenges that surrounded the original premise of a practical production lockback. “The lockback actually is a bar that goes across the back of the blade with the spring under it, and when you push down on the bar it rocks on a stainless rivet,” he said. “So, that was always hard to get exact because you did not want it to be loose and it needed to fit perfectly.
“You need to do fine blanking of the blades to achieve that and for years components had been machined, but with fine blanking you can get that done. We worked with the design for quite a few months, and it was all new to us. That was in 1963. The first knives on the market totaled about 250 in 1964, and then in 1965 we ended up making about 10,000 of them. It just grew from there. The 110 continues to be one of our most popular knives, and we are producing them now at a rate of over 1,000 per day. We have a whole crew that just makes the 110 folding hunter. To Buck, it has been something that has sold every year, and it just keeps getting better.”
Over the years, there have been a few tweaks to the lockback design of the Buck 110. For example, during the 1970s it was discovered users were placing a great deal of pressure on the blade and the brass rivet in the mechanism itself was shearing. The brass rivet was replaced with a stainless steel component, and the 110 continues to sell well around the world. From large retailers to mom-and-pop hardware stores, from Main Street to Moscow, the Buck 110 is a knife user’s mainstay.
No Excess Motion
From a custom perspective, knifemaker Steve Hoel has wrestled with the lockback in his shop. “They’ve been making lockbacks for years, and everybody is making them now,” he remarked. “If the lockbacks are engineered right and the angles are right, then you have no excess motion. It’s simple to operate and strong, and can be done without a lot of expensive equipment. The lockback can be made with nothing more than a file if you know what you’re doing. They’re tough but, if they’re made right, you can eliminate all the slop and rattle.
“I don’t think there are a lot of big weaknesses in the lockback. They’re more complicated to make right than a LinerLock™, and you’ve got to understand some engineering principles. It isn’t rocket science, but there’s some science involved, and Ron Lake [helped write] a book [How To Make Folding Knives] that you can read to help make a good knife. You can come up with some mechanisms that will work well and are reasonably simple, but you can’t scale them down to a small knife without running into problems. A lot of the strength of the lockback depends on the width of the lock bar and the position in front, back or above the blade. If you don’t pay attention, you can get down to some weak points.”
The lockback mechanism itself, particularly among custom makers, has seen some streamlining and refinement over the years. While the principles are constant, improvements relate to the availability of better materials and higher-quality fit and finish. Some older lockbacks could not stand up to a lot of hard work and were clunky or overbuilt.
“I started out taking old knives apart and fixing them and modifying things in them,” Hoel recalled. “If you back up 60 or 70 years ago, the old pocketknives had 90/1000ths holes with 84/1000ths pins in those holes a lot of times, so it was not like using a taper pin or bushing that holds things solid. The ones we make now are more solid, primarily through better craftsmanship and materials that have evolved.”
The Human Element
Claussen asserts another aspect of the popularity of folding knives and of lockbacks in particular has to do with human nature. “It’s their mystique,” he related. “People seem to have a fascination for complicated things, plain and simple. This is generally true in life and very specifically in the collecting field. Watches, clocks and other collectibles are favored because of their complication. The general rule, with all things being equal, is that the more complications, the more desirability, hence greater value. To have a locking feature with a knife definitely adds mystique, aura and increased value.”
Perhaps therein lies the secret to the success of the Buck 110 and other production or custom lockback folders that have reached such prominence. Practical, strong lockup increases safety and security in operation. Folding knives carry more easily than fixed blades, and it can be argued that their deployment is somewhat easier than that of a fixed blade in certain situations. Modern materials and knifemaker experience have enhanced the quality of the lockback on all fronts, and the mechanism has become accessible to the general public like never before.
Still, there is something about that tight, solid lock, the feel in the hand of the user, which makes the lockback so special and so timeless.
For more on the latest knives, knife legislation, knifemaking instruction, knife trends, knifemakers, what knives to buy and where and much more, subscribe to BLADE® Magazine, the World’s No. 1 Knife Publication. For subscription information click on http://www.shopblade.com/product/blade-magazine-one-year-subscripti…?r+ssfb021712#BL1SU
Knife Guide Issue features the newest knives and sharpeners, plus knife and axe reviews, knife sheaths, kit knives and a Knife Industry Directory.
Get your FREE digital PDF instant download of the annual Knife Guide. No, really! We will email it to you right now when you subscribe to the BLADE email newsletter.
Click Here to Subscribe and get your free digital 2022 Knife Guide!