Home Blog Page 151

BLADE Show West 2018 Award Winners List

0

BLADE Show West 2018, taking place Oct. 5 to 7 at the Oregon Convention Center in Portland, recognized achievement in knifemaking with custom and factory awards. Entrants all exhibited at BLADE Show West also. A secret panel of judges determined the winners based on a variety of factors.

Below are photos of the winning entries. Congratulations!

Custom Knives

Best in Show & Best Fixed Blade

Aaron Wilburn, Wilburn Forge

Best in Show

 

 
 
 
 
 
View this post on Instagram
 
 
 
 
 
 
 
 
 
 
 

 

A post shared by Aaron & Francesca Wilburn (@wilburnforge) on


Best Folding Knife

PH Jacob Custom Knives

Best Folding Knife BLADE Show West 2018

Best EDC Knife

PH Jacob Custom Knives

Best EDC Knife BLADE Show West

 

 
 
 
 
 
View this post on Instagram
 
 
 
 
 
 
 
 
 
 
 

 

A post shared by Phil Jacob (@p.h.jacobcustomknives) on

Best EDC Non-Knife

Olamic Cutlery

Best EDC Non-Knife

 

 

 
 
 
 
 
View this post on Instagram
 
 
 
 
 
 
 
 
 
 
 

 

A post shared by Olamic • Never The Same (@olamic) on

Best “Weird” Knife

Ooak Forge

 

Custom pizza cutter

 

 
 
 
 
 
View this post on Instagram
 
 
 
 
 
 
 
 
 
 
 

 

A post shared by Harlan Whitman (@ooakforge) on

Factory Knives

Best in Show & Best Folding Knife

WE Knife 704DS

 

Best in Show BLADE Show West 2018

Best Fixed Blade Knife

Bradford Guardian 4.5

Bradford Guardian 4.5

Best EDC Knife

WESN Microblade

Best EDC Knife BLADE Show West 2018

Best EDC Non-Knife

CRKT Williams Tactical Key

 

Best EDC Non-Knife BLADE Show West

Best “Weird” Knife

Zombie Tools Hurley

Best Weird Knife BLADE Show West 2018

 

7 Ways BLADE Show West is Different from BLADE Show

0

Portland knife show

Other than the name, what sets BLADE Show West apart from BLADE Show? They’re both dedicated to knifemaking, knife collecting and appreciating the rich tradition of knives, but there are a few things that set them apart.

And just so we’re clear:

  • BLADE Show: Takes place annually in early June in Atlanta
  • BLADE Show West: Takes place in Portland, Oregon, with the first installment happening Oct. 5-7

1) Location

Oregon knife showWith the BLADE Show firmly ensconced as the world’s largest and most important knife event—next year’s rendition will return to the Cobb Galleria in Atlanta June 7-9—show officials decided to offer a sister show in Portland, Oregon, to spread the sharp cheer to western BLADE Show fans who can’t make the trip southeast. It takes place at the Oregon Convention Center.

2) EDC Gear

In addition to knives, you’ll find loads of everyday carry gear to round out your daily ensemble. This includes anything and everything that’s handy and sized for pockets. Check out the full exhibitor list here to get a feel for what this means.

3) New Awards

Knifemaking awardsBLADE Show West’s exhibitor awards will be a mix of the old and new. Custom and factory knives will each have the same categories: Best in Show, Best Fixed Blade, Best Folding Knife, Best EDC Knife and Best “Weird” Knife. Each also will have a Best Non-Knife EDC category for a tool or item that, as the name notes, is not a knife.

The Best in Show, Best Fixed Blade and Best Folding Knife are all self-explanatory. One proviso with the Best in Show is that, like at the BLADE Show, it is the category-winning knife judged best of all the category winning knives. The Best Non-Knife EDC will not be eligible for Best in Show. (Hey, after all, this is a knife show.)

The Best EDC Knife must be “a knife designed to be carried easily on an everyday basis for everyday cutting and other knife needs. It can be a fixed blade or folder, though if a fixed blade it must have a sheath or other carry system that makes it easy to carry on a daily basis.”

The Best Non-Knife EDC must be “a tool or item designed to be carried easily on an everyday basis for everyday needs.”

The Best “Weird” Knife will be a “knife that is best in keeping with Portland’s unofficial motto of ‘Keep Portland Weird.’ The motto is designed to promote ‘individuality, expressionism, local art’ and ‘atypical lifestyle choices and leisure activities.’ In other words, the sky’s the limit on this category. The weirder, the better.”

4) Laid-Back Programming

October 2018 knife shows

Unlike the BLADE Show and its BLADE University and demos, BLADE Show West will go for more of a laid-back approach to its seminars and demos, focusing more on quality than quality and quantity. All seminars and demos are free to BLADE Show West ticket holders.

With some of today’s top custom makers in attendance there will be a focus on knifemaking, including from the standpoint of the beginner and experienced knifemaker, as well as the buyer and collector of custom knives.

Click here to see the full schedule.

5) Roundtables

Two of the hottest genres in custom knives are slip joints and chef ’s knives, and BLADE Show West assembles some of the leading names in both categories for roundtable discussions.

Award-winning knifemaker Bill Ruple, along with some of his well-known pupils, will host a roundtable about the keys to the best custom slip joints, the importance of the mentor/mentee relationship and more.

Custom chef ’s knives have been hot for some time now and BLADE Show West has two of the leading authorities on both selling and making those knives: Daniel O’Malley of The Epicurean Edge/Bladegallery.com and ABS master smith Bill Burke, respectively. Join them as they decipher exactly what makes outstanding chef ’s knives.

See more here.

6) No Sales Tax

Unlike Georgia, Oregon doesn’t have a sales tax. That means you can put what you save toward something else, like another knife, a cool EDC gadget, some fun after the show, or, heck, lunch.

7) Reduced Ticket Pricing for Tiny House Expo

The Tiny House Expo takes place Oct. 6-7 adjacent to BLADE Show West. Your BLADE Show West ticket will earn you reduced entry to that show (and vice versa).

More Information

Find more information about attending BLADE Show West here. Hope to see you there!

A Custom Gentleman’s Takedown Combat Utility Knife?

0
Custom takedown knife
The Tuxedo Fighter is a takedown combat utility knife by Tim Steingass. The takedown tool at upper right fits into the two tiny holes in the piece at bottom center, which is the linchpin for disassembly and assembly. At press time, Tim said he had so many orders he had closed his books. (SharpByCoop knife image)

The Tuxedo Fighter by Tim Steingass is a takedown combat utility knife the maker quipped is for guys “who like Tinkertoys®”—those who enjoy taking their knives apart and putting them back together.

Custom fighter knifeAs for the Tuxedo name, Tim said he got the idea for it from one of his customers for whom he made repros of three Bob Loveless small fighters.

“He got one with an ivory Micarta® handle and liked it so much he wanted a black-handled one,” Tim recalled. “I imagined he was going to wear it under his tuxedo and that gave me the idea for the Tuxedo Fighter.”

The fact that the fighter is small and fancy also seemed to fit the Tuxedo moniker.

“It’s not tactical, it has a shiny blade and beautiful, shiny handle, and all the fittings are polished and pretty and it comes with a horizontal, ambidextrous sheath,” Steingass added.

Made to be broken down and maintained, “the takedown is a great way to take care of a knife. It just shows the craftsmanship of the knife, frankly.”


See More Incredible Custom Knives at BLADE Show West

Portland knife show

 

Knife Review: Factory vs. Custom Version of Similar Knife

Factory versus custom knife review

 

We The People custom knife review

MOTAC by Doublestar factory knife review

Factory vs. Custom: A Knife Review Battle for the Ages

The blades of both the MOTAC by Doublestar and We The People by Brad Mock have somewhat of a triangular appearance. This provides a very sharp tip for fine work and a wider base for heavier jobs. I decided to start at the tip of each blade and work my way back.

Knife Test: Paper Cuts

Knife test paper cut
The WTP sliced the copy paper great at the midway point to the tip, but the edge started to thicken toward the grip and was unsuited for slicing. The MOTAC was smooth and cut aggressively along the entire edge.

First up was a quick edge check by slicing 20-pound bond copy paper. Brad’s knife sliced great at the midway point to the tip. From midway to the start of the cutting edge it has a thicker edge geometry unsuited for slicing.

The Doublestar knife was smooth and aggressive along the whole edge, giving me nice slicing sounds.

Knife Test: Cardboard

Knife test cardboard cut

It was time to thin out the cardboard pile. The MOTAC sliced smoothly and was very controllable. The thickness of the blade twisted the cardboard as I was cutting but did not affect the slices. We The People sliced very smoothly and cleanly. The handle shape made it easy to control.

My wife, Melissa, had purchased a new lounge chair. The box it came in had corner supports of compacted cardboard, solid and heavy duty—perfect for chopping. We The People chopped an average of 3/8 inch deep. The MOTAC averaged the same depth. This is some tough cutting medium, for sure.

Knife Test: Whittle

It was time to relax and whittle a spell. The MOTAC was very smooth at the pursuit. It gave great curly-cues and was extremely controllable. I really liked the deep choil.

We The People was choppy with the curly-cues. I had to increase the angle of my cut to dig deeper. The edge geometry was on the thicker side. The handle was very comfortable during use.

Knife Test: Rope Cut

Rope cut knife test

Next up was the rope cut. I untwisted a 1-inch manila rope and used one of the 3/8-inch strands. We The People started off crunching until at 50 cuts the edge started to slide. The deep etching seemed to slow the blade down some. The handle was very comfortable during the push cuts. The MOTAC crunched to 135 cuts before the edge started to slide. The handle was slightly rough on my hand during the push cuts.

Knife Test: Brass Rod

Knife flex test
Both knives flexed on the brass rod without chipping or dulling, an indication of good heat treatment on each.

To check the flexibility of the edge I employ the brass rod test. Both knives flexed without chipping or dulling, an indication of good heat treatment by both makers.

Bottom Line

I liked the feel of the We The People and the function of the Doublestar.

Suggestions

I would soften the handle edges on the MOTAC a little and decrease the edge angle on We The People.


BLADE Show West 2018 information

Knifemaker Brian Tighe to Present Damacore at BLADE Show West 2018

0
Knifemaking class
The Tighe Fighter, by Brian Tighe. (Eric Eggly, PointSeven Studios photo)
Brian Tighe knives
Brian Tighe

The 2018 BLADE Show West seminar slate received another shot in the arm today with the announcement that award-winning knifemaker Brian Tighe will participate in the seminar, “Damacore: Damasteel’s Hot New Blade Laminate.” BLADE Show West will be Oct. 5-7 at the Oregon Convention Center in Portland, Oregon.

“Brian was among the first to use Damacore and has the most experience working in it up to now,” noted Damasteel’s Per Jarbelius, who also will participate in presenting the seminar. “As a very experienced knifemaker in general and with Damasteel, Brian will have valuable input to contribute.”

The presentation will be part of the show’s “Steel Day” of seminars, which also will include “Nitro-V: The New Super Steel.” Join Peter Bruno and Dale Cucos of New Jersey Steel Baron as they outline this hot new blade steel.

Complete BLADE Show West Seminar Schedule

Portland knife show

 

FRIDAY, OCT. 5: GET SHARP DAY

1 p.m.-2 p.m.: “Knifemaking 101 Q&A”—ABS master smith Bruce Bump and bladesmith Mike Pierce will offer professional tips on how to get started making knives, including how to learn, classes to take, shop tips, tools to buy, the things to do and not do, and more.

3 p.m.-5 p.m.: “How To Sharpen With The Latest Sharpeners”—In back-to-back one-hour sessions, representatives of Work Sharp and Wicked Edge Sharpeners will demonstrate how to get a razor-sharp edge on a knife with the latest sharpener of their respective companies.

SATURDAY, OCT. 6: KNIFEMAKING DAY

11 a.m.-12 p.m.: “How To Put a Handle on Your Knife”—David Tuthill of Fire Horse Forge will demonstrate, with the help of a Burr King grinder and his own equipment, how to attach a wooden handle to a knife.

1 p.m.-2 p.m.: “How To Make a Flowed-In Guard”—ABS master smith David Lisch will show you how it’s done on a Burr King grinder outfitted with a small wheel attachment.

2:30 p.m.-3:30 p.m.: “Custom Chef’s Knife Roundtable Discussion”—ABS master smith Bill Burke and Daniel O’Malley of Epicurean Edge will talk about one of the hottest genres of custom knives, including their hottest custom examples, how they’re made, how they’re used and who uses them—including professional chefs—and more.

4 p.m.-5 p.m.: “The Road to World-Class Custom Slip Joints”—Award-winning multi-blade maker Bill Ruple and two of his top pupils—award-winning makers Rusty Preston and Luke Swenson—will conduct a class on how they have come to be among the custom industry’s top makers of slip joints, including the mentor/pupil relationship, the keys to making the best slip joints and more.

SUNDAY, OCT. 7: STEEL DAY

11 a.m.-12 p.m.: “Damacore: Damasteel’s Hot New Blade Laminate”—Per Jarbelius of Damasteel will outline the performance, strength and beauty of Damacore, Damasteel’s new laminated knife blade material with a center made of high nitrogen steel.

1 p.m.-2 p.m.: “Nitro-V: The New Super Steel”—Peter Bruno and Dale Cucos of New Jersey Steel Baron will tell all about New Jersey Steel Baron’s Nitro-V, one of the latest high-performance blade steels being used by a growing number of custom knifemakers.

More Information about BLADE Show West

For more on BLADE Show West, visit bladeshowwest.com.

Join Knifemakers and Knife Collectors in Portland for BLADE Show West 2018

0

Portland knife show

  • Dates: Oct. 5-7, 2018
  • Location: Oregon Convention Center in Portland, Oregon (777 NE Martin Luther King Jr Blvd.)
  • Show Hours: 10 a.m. to 6 p.m, on Oct. 5-6; 10 a.m. to 4 p.m. on Oct. 7
  • Tickets: Buy them online here
  • More Information: Visit the website

BLADE Show is Headed West to the “Knife Capital of the United States”

Best knife showsJoin your friends at BLADE magazine and the knife industry at-large Oct. 5-7, 2018, at the Oregon Convention Center in Portland for BLADE Show West.

It is the best place to engage expert knife handlers, precision craftsmen, and master knifemakers in one location. Explore your passion for knifemaking and knife collecting while checking out high-end blades and everyday gear.

Plus, learn a new skill during exhibitor demos and chat with your favorite knife and gear makers in-person.

200+ Exhibitor Booths and Tables

Where to attend knife showsFind brand name knives, one-of-a-kind custom knives, edc gear and materials from industry leaders like Smoky Mountain Knife Works, CRKT, Kershaw, Benchmade, Leatherman, WE Knife and more.

See the full list of exhibitors here.

FREE Exhibitor Demonstrations

Take your knife knowledge to the next level as you learn from industry professionals and see firsthand how knife legends craft, sharpen and forge their knives. Learn everything from how to grind a knife blade to all about Nitro V, the new super steel. All demos come free with the purchase of any BLADE Show West ticket.

See the demo schedule here.

Awards

See which exhibitor wins a BLADE Show West award, with separate categories for both custom and factory makers. Keep an eye out for the best “weird” knife, too!

About

BLADE Show West is brought to you by BLADE and Caribou Media LLC, hosts of the largest knife show in the world, BLADE Show, each June in Atlanta. After 37 years, BLADE Show is expanding to Portland for BLADE Show West.

Knives and Swords 101: What are Menuki?

0
Menuki definition
Shaped like a dragon, bat and lion, menuki (handle charms) are tucked under the cord-wrapped stingray skin
handles of a trio of tanto knives by RJ Martin. (SharpByCoop image)

In Japanese sword culture, menuki are handle charms, often tucked under the silk wrappings of stingray skin grips. Like all aspects of Japanese swords, the charms are handmade—fashioned one at a time, sculpted, carved and engraved. They are for decorative purposes only, though one could argue that, if appropriately shaped, they’d add palpability, and perhaps, if lucky charms, good omens for sword wielders.

Knife charms
Along with “Agyo” and “Ungyo,” two Japanese temple guardians, engraved on the VG-10 blade of the “Yari” spear, this knife by Glenn Waters also sports an ebony handle and a silver dragon handle charm.

Knifemakers being knifemakers, whether American, German, Nordic, Australian, Indian or South African, these little handle charms have not gone unnoticed. They’ve been adopted by knifemakers wanting to add more elements of intrigue to their knives.

A knife’s ability to perform the cutting chores for which it was designed is the first priority, but ask any knifemaker, and he or she will tell you that form follows function. And sometimes it’s the aesthetics of a knife that catches the eye of a potential buyer.

So knifemakers pay attention to the details. They add amenities, embellish the pieces and fashion handle charms. And knife collectors are charmed, we’re sure.


See More Unique Knives at BLADE Show West 2018

BLADE Show West 2018 information

Advertisement

Must Read Articles

Read this before you make a knife

Knifemaking 101 – Read This Before You Make a Knife

  by Wayne Goddard My experience has taught me that there's nothing like digging in and getting started. I've often said the hardest part of the...
how to forge damascus steel

How to Forge Damascus

Advertisement
Advertisement