The OKNIFE Beagle emerges from testing as one well-bred blade.
The Beagle by OKNIFE is a mid-sized folder that rides great in a pocket—big enough to handle most cutting chores but small enough to be comfortable to carry every day. As a heavy knife user, I always carry. It has to ride comfortable and perform or I won’t consider it. The Beagle was on my side for 30 days with no carry issues. Check the first block. Now for the performance side.
The Beagle was very sharp out of the box. A quick paper slice with 20-pound bond copy paper proved it. Via a push cut it sliced quite smoothly with no snags or tears. The handle shape made for easy control of the width of slices.
Next up: single-walled cardboard. The Beagle made zipping noises during the push cuts. Again, it was very controllable on the slice widths, nice and aggressive on every pass, with no snags or tears.
A scrap piece of 8-ounce leather was next. I sliced it similarly to the cardboard to see if I could get the same zipping noises. The Beagle didn’t disappoint. It zipped and crunched during every cut. I really liked the forcefulness in the leather cutting.
The knife made thin, even slices in the 8-ounce leather. The handle shape aided in controlling the thickness of each cut.
Using another piece of leather, I did some skiving. The knife made thin, even cuts. As noted, the shape of the handle really aids in controlling the thickness of the cuts. The blade was smooth and uncompromising on each slice.
I grabbed some scrap pine and whittled a bit. The Beagle produced excellent curlicues, taking deep bites. The notches on the blade spine are just grabby enough to keep your thumb in place without abrading it. There were no hot spots on the handle.
The Beagle took deep bites in producing excellent curlicues. The notches on the blade spine are just grabby enough to keep your thumb in place without abrading it.
STRENGTH TEST
Baton cutting with a linerlock folder is not recommended but I did it anyway. On the other hand, it is a serious strength test for the lockup and liner. After several whacks there were pine pieces all over the work bench. The lockup stayed at 100 percent on every whack. The handle was comfortable throughout.
Baton cutting with a linerlock folder is not recommended but the author did it anyway. On the other hand, it is a serious strength test for the lockup and liner. After several whacks the lockup stayed at 100 percent, though the spring does appear to engage the tang too far to the right (inset). Upon later examination, however, the spring had returned more toward the left, possibly due to repeated opening/closing of the knife.
It was time to break out the half-inch sisal. The Beagle made 192 crunching cuts in the rope. I was surprised at how comfortable the handle was during cutting—not a single hot spot, warm spot or liner pinch. I’m very pleased OKNIFE paid attention to this detail. Job well done!
The Beagle made 192 crunching cuts in the half-inch sisal rope. The handle was comfortable throughout—not a single hot spot, warm spot or liner pinch.
The last test for the edge and lock was chopping into a whitetail deer antler. Thirty hard whacks later and the edge had no damage. The lock was just as tight as when I started—100 percent.
In the final test, the Beagle chopped the antler 30 times with no edge damage. Verdict: heat treat spot on!
CHANGES
Maybe a few grooves in the handle for added grip?
BLADE GRADE
With its comfortable handle and sharp blade, the Beagle is a great folder for everyday carry.
OKNIFE BEAGLE Specs
Blade length: 33/8” Blade steel: 154cm stainless Blade grind: Flat Blade finish: Satin Blade pattern: Harpoon Blade opener: Thumb stud Handle: Green canvas Micarta® Lock: Linerlock Liners: Stainless Pocket clip: Yes Weight: 4 oz. Closed length: 4.25” Country of origin: China MSRP: $79.95
Few knives have served America more than those of the U.S. military.
Editor’s Note: This is the first of a two-part series on the most influential knives to serve the U.S. Military and explores some of the early influences on military knife design.
As what many call the greatest country in the history of countries approaches its 250th birthday, now’s a good time to salute some of the top knives that played pivotal military roles in the forging of the world beacon that is the United States of America.
It is, of course, impossible to recognize in one magazine story every single knife that played a crucial role in the many battles of the wars fought by the USA. However, with the help of some of the knife industry’s leading military authorities—including several of whom have seen the elephant in service to our nation—BLADE® will endeavor to touch on some of the more consequential knives of U.S. military history.
Before embarking on such a quest, the first task is to identify a basic group of the most indispensable knife types over two-and-a-half centuries of American land warfare. At the risk of omitting one or more, five stand out: bayonet, all-purpose utility fixed blade and/or bowie, dagger, machete/chopper and utility folder.
Michael Price recognized that to create a viable knife for self-defense and combat, form must follow function. His solution was to use the full-tang construction method, here on one of his classic mid-19th-century daggers. (Image courtesy of Louis Chow)
“These encapsulate everything that an infantryman used during the 250-year history of our country,” noted Louis Chow, a 24-year U.S. Army veteran who retired with the rank of major and is one of the leading collectors of the knives of BLADE Magazine Cutlery Hall-of-Fame® member Bob Loveless. “The bayonet, of course, from the get-go, from the Revolution to today.”
Louis indicated the all-purpose utility fixed blade/bowie could include privately purchased knives such as the Randall Model 1 and, of course, double-guard bowie types like the USMC fighting utility knife, aka the Ka-Bar. He pointed to the mid-19th-century designs of Michael Price as highly influential on daggers through to today, and machetes such as those made by Collins used in the Spanish-American War and before to Vietnam as vital to U.S. war efforts. Though pocketknives were indeed carried by American patriots during the Revolutionary War, the utility folders to which Louis referred are more of the modern Leatherman/Gerber multi-tool type, not to mention the Buck 110, Al Mar SERE, CRKT M-16 and others. As Louis noted, almost every soldier, male or female, in the modern military carries a multi-tool folder.
Many knife enthusiasts know that bayonets are rarely, if ever, used in combat today, nor have they been for well over a century. “It’s hard to actually find someone who used one in combat,” Louis said. Probably the most legendary American bayonet charge was the eminently successful one by Union forces led by Col. Joshua Chamberlain against Confederate troops down a hill called Little Round Top, a major turning point in the Battle of Gettysburg and, of course, the entire Civil War. Ironically, as Louis noted, “the most famous bayonet charge of all was the last one.”
While bayonets have rarely been used in American combat for many decades, that does not mean they do not remain significant teaching tools in today’s U.S. military. “When I was a company commander in 1990, we trained with the bayonet,” Louis recalled. “There are established bayonet courses on every installation, such as Fort Hood in Texas and Fort Benning in Georgia, and we would go there and train with the bayonet.” The rifles and bayonets have changed over the years but the bayonet training techniques remain the same. Throughout U.S. and nearly all other nations’ histories, governments have been responsible for the issuance of combat knives in the form of bayonets for their infantry fighting forces. During World War II, the USA issued all-purpose fighters and utility knives to many soldiers, sailors and airmen. However, as Louis noted, privately purchased edged tools and weapons have always been the mainstay of our servicemen. During the earliest American conflicts, including the Revolutionary through the Civil Wars, kitchen, utility, farrier-forged and European-imported cutlery were the sidearms of the multitude of militiamen and patriotic volunteers.
The original Applegate-Fairbairn Folder was a collaboration between Col. Rex Applegate and knifemakers Bill Harsey and Butch Vallotton. Harsey stated that a Gerber official said the Army ordered 50,000 of the knife at one time for the troops. At bottom is the original prototype and at top is a first-production Gerber version autographed by Applegate. (From the collection of Michael Janich)
The knife carried and made famous by Cutlery Hall-of-Famer James Bowie in the 1820s and 1830s was copied in various forms by makers worldwide and served as inspiration to any number of fixed blades carried in the U.S. military. Another large fixed blade that met with success in military circles was the Rifleman’s Knife made by the Ames Mfg. Co. circa 1860. Ames also made the Dahlgren Bowie Bayonet around the same time. Collins & Co. made a variety of bowies/machetes, the most famous probably being the No. 18, also incorrectly called the V-44 by many (according to D.E. Henry in his book Collins Machetes and Bowies 1845-1865, V-44 was the real name of a 1944 Case Survival Knife, not the No. 18).
Generational Blades
Circa the mid-19th century, Michael Price was considered one of the premier cutlers in the western United States. He was best known for exquisite presentation knives that incorporated marine ivory and a variety of beautiful shells. However, as Louis wrote, to create a viable knife for self-defense and combat, Price recognized that form must follow function. His solution was to use the full-tang construction method. And for a century and a half, some of the most notable American cutlers adopted the full-tang method that significantly improved a knife’s dependability and durability.
Early in 20th-century Michigan, Cutlery Hall-of-Famer William Scagel began forging axes and knives of various sizes and styles. He made most of his utility, hunting and bowie knives via the hidden-tang method. Though some of his combat knives were also hidden tang, many others employed the full-tang method.
“It was purported that the Scagel hidden-tang fighters with stacked leather washers were made for the European theater, while the full-tang fighters with wood-slab handles were made for the Pacific theater,” Louis wrote. “It was believed that stacked leather washers would be too susceptible to the humidity, high temperatures and salty air” of the applicable Pacific region. As a testament to Scagel’s outstanding craftsmanship and exceptional design, many of his fighters survived the war in good condition.
William Scagel’s hidden-tang fighters with stacked leather washers reportedly were made for the European theater during World War II, while the full-tang wood-slab fighters were made for the Pacific. The stacked leather washers were thought to be too susceptible to the humidity, high temperatures and salty air of the applicable Pacific region. (Image courtesy of Louis Chow)
In 1937, Cutlery Hall-of-Famer W.D. “Bo” Randall observed an older man scraping the bottom of a boat with a knife that appeared undamaged by the abuse. Intrigued by the improvised tool, Bo purchased it from the owner and contacted its maker, who just so happened to be Scagel. Randall eventually became Scagel’s student and soon opened his own shop, making Scagel-style knives.
“At the onset of World War II, Randall designed and produced some of the most recognizable combat knives ever made,” Louis stated. “Nonetheless, all were made with the hidden-tang method. It was not until the early 1960s that Randall introduced the full-tang Model 14-Attack and the Model 15-Airman combat knives.” Continuing the generational theme, Cutlery Hall-of-Famer Bob Loveless read a magazine article about Randall knives in 1953. He corresponded with Bo and made his interpretations of Randall knives before experimenting with and then making his own full-tang models.
From the mid-1960s through the early ’70s, Loveless accepted many orders from service members awaiting assignment to Vietnam. He also received bulk orders from units stationed there. One bulk order in early March 1967 from a unit commander in the 1st Cavalry Division was for 37 fighting knives.
“The unit commander and his troopers were stationed in Saigon and were supporting Operation Junction City, one of the largest airmobile operations in the war,” Louis wrote. “As a patriot and former veteran himself, Loveless would temporarily halt all other orders and place top priority on knives destined for combat. As for those 37 fighters, he worked day and night and completed the order in less than a month. For the next four decades, the Loveless full-tang designs were copied and reinterpreted by countless knifemakers and knife companies in the United States and abroad.”
In addition to the foregoing cutlery legends, the full-tang method was also preferred by many other U.S. World War II knifemakers. Among them: Alfred Bimson, John Ek, Taylor Huff, A.R. Kephart, Kennedy Arms, Bob Riggs, Ernest Warther and Cutlery Hall-of-Famer M.H. Cole. Cole also authored the comprehensive U.S. Military Knives, Bayonets & Machetes series of books and has been dubbed the “Sage of Military Knives” by Cutlery Hall-of-Famer Bruce Voyles. Continuing Cole’s legacy is knifemaker/author Michael Silvey through his reproductions of Cole’s designs and his lavishly illustrated books on the knives of the United States military in World War II and Vietnam, and other works.
The Spyderco Paramilitary 2, simply known as the Para 2, is a part of the Military family of popular tactical folders in the Spyderco lineup. The Para 2 came about as a downsized version of the full-size Military model, answering the call from customers for a practical EDC option.
Smaller it might be, but the Para 2 retains the essence of what makes the Military a popular working folder. And because of this, the knife has developed a cult following. However, it’s not simply a shrunken-down facsimile of its larger predecessor, having gone through several design improvements that have dialed in the knife to users’ needs.
In this article, we’ll examine exactly what has made the Spyderco Para 2 such a winner in the company’s lineup. And why, if you need a truly rugged everyday option—or just want a classic in your collection—the legendary knife more than fits the bill.
Para 2 Blade
To start things off, the blade of the Para 2 sports a useful clip point shape, enhanced with a full flat grind. Furthermore, the knife has a gradual distal taper from the tang to the tip, evident when viewed from the top. The length of the blade measures 3.4 inches long, enough length to take care of heavy work but short enough for comfortable carry in a pocket.
A CPM S45VN stainless-steel blade brings toughness, excellent edge retenion and easy of sharpening to the game.
Constructed of CPM S45VN high-performance stainless steel, Spyderco picked the perfect material for a high-end knife. Compared to the gold standard of this class—S30V—S45VN proves a bit tougher, yet is remains easy to resharpen. That is if you have to. The blade’s toughness means it holds an edge extremely well, suiting it for long-haul work without interruption. A final point, S45VN is fairly renowned for its corrosion resistance, making the Para 2 excel in nearly any environment.
As those familiar with Spyderco can guess, the blade boasts the company’s trademark hole near the spine, at the rear. This has been the go-to deployment method for time immemorial on the firm’s knives. Rounding things out on the blade, there’s integrated chill formed by part of the blade and handle when the blade is opened. A choil permits the user to further choke up on the blade for extra control when needed.
Para 2 Handle
Spyderco opts for a black textured G-10 for the handle, which endows it with a few assets. First, it keeps the knife nimble, cutting down on the Para 2 overall weight. But this isn’t at the expense of strength—G10 is tough as cut nails—and a solid purchase on the knife.
Dark, dashing and useful, the Para 2’s G-10 handled gives users a firm grip on the knife.
The handles are milled out, allowing the slightly undersized stainless steel liners to sit flush with the G-10. Nicely, this reduces the overall width of the handle but doesn’t sacrifice the lateral strength of the liners. Spyderco also turns its eye to weight reduction with the liners, porting them to further lighten the load—while not compromising strength.
The handle shape itself is very ergonomic, like the full-size Military. There is an expanded, curved section that forms an integral finger guard to prevent your hand from sliding forward. The handle feels very secure in hand, and this inspires user confidence.
Compression Lock
With an extremely strong lockup, the Para 2’s Compression Lock adds confidence to the system.
The Para 2 utilizes Syperco’s Compression Lock to secure the blade, a solid system that has several benefits. For those unfamiliar with the mechanism, it’s an in-house design that provides an extremely strong lockup. It operates by the lock bar wedging itself onto a ramp on the blade’s tang and a hardened steel stop pin. As an added benefit, the release is situated on the handle spine, just behind the blade within reach of the thumb and forefinger. Not only is the design ambidextrous, but it also facilitates fast and intuitive one-hand opening (with a bit of practice) and closing.
Pocket Clip
A steel pocket clip is attached to the handle in the right-hand, tip-down configuration. However, Spyderco has what they call 4-way clip mounting with the Para 2. This means the handle is drilled and tapped to modify the clip’s position, thus the carry style. Again, this makes the knife lefty- and righty-friendly, as well as allowing for tip-up or tip-down carry. Understandably, this is another facet of the Para 2 has that a lot of fans.
No matter how you carry or hand you use, you can move the clip to suit your needs.
The handle also has an open build, allowing you to effectively clean lint and other debris out of the inside of the handle by using either compressed air or tap water. The handle length is 4.8 inches, making the overall length of the Para 2 around 8.2 inches. I would consider any folder with an overall length of 9 inches to be large, so to say the Para 2 is a midsize folder is a stretch. It’s safer to say it’s on the upper end of being midsize. Still kind of compact, but large enough to handle some man-sized cutting jobs.
Para 2 In Action
The flat ground blade with distal taper helps the blade sail through anything with ease. This is exactly the reason why the full-size Military is a favorite among knife users the world over. You’ll notice the blade bites in and does so aggressively and it just takes off. Shoot, I have even used my Para 2 and Military in the kitchen to aid in food prep at times. The Para 2 makes for an effective paring knife.
An all-time classic, the Para 2 offers users an option fit to tackle most jobs.
Outside of the kitchen, the Para 2 slices through cardboard, plastic edging, styrofoam blocks, and even strips wire with ease. Spyderco’s cutting edges out of the box are nothing short of perfect. The Para 2 can be put to work immediately without modifications to the edge. S45VN’s durability is out of this world. You’ll benefit from the enhanced edge-holding capability of this steel by not having to sharpen as often. However, all this depends on your frequency of use and that can vary from person to person.
The handle ergonomics are very comfortable. The Para 2 didn’t leave any hot spots of any kind and is pleasurable to wield during extended periods of use.
Final Cut
I think you will find the Para 2 to be an excellent daily carry choice for you, if you are looking for a working folder that is also a super comfortable EDC knife. As for how much the Spyderco Paramilitary 2 will set you back, the MSRP starts at $265.00 for the black G-10 handle/satin-finished blade as tested here. There’s also a camo handle for the same price, and black DLC coated versions for a bit more at $285.
Master smiths explore the symmetry, skill and survivalist roots of a classic.
It’s part adventure with a bit of notoriety and a dash of creativity. For the modern custom knifemaker, several styles are brought to life with history in mind. And the push dagger is one of them.
Maybe seldom seen, but always intriguing, push daggers trace their lineage to a bygone era when self-defense at the card table or on the street meant quick deployment from a vest pocket. For sure, that perspective spurs some custom makers to insert the push dagger into their repertoire while the stylized and subtle blend of blade and handle combine for a unique test of shop skill.
“They’re a backup tool,” explained ABS master smith and BLADE Magazine Cutlery Hall-of-Fame® member Steve Schwarzer. “They were typically carried in the 1700s and 1800s along with a one-shot pistol. After that shot, the push dagger was the next position. It’s been around for a long time as an extension of your arm with a blade, and it is hard to take away from somebody that is skilled in its use.”
Schwarzer’s featured push dagger with stag handle and evocative faces carved on both ends is 5¾ inches long with a 3¾-inch blade of mosaic damascus steel. He has actually made two push daggers in this style and designed another for Benchmade about 20 years ago. “For me, they’re fun, and that’s why I like to make them,” he commented. “I’ve always had a fascination about them and adapted my martial arts background to training with them. The design traditionally is with a very short blade, and in martial arts, it has to do with the alignment of the hand and arm bones, along with the shape of the blade, which is double-edged traditionally. Everything in nature is curved for an effective cutting surface.”
Harvey Dean Tejas
Why a push dagger? Harvy Dean (inset) puts it succinctly, “They’re just cool.” That certainly holds true for his Tajas push dagger, with an elegant feather damascus blade, 24k gold raised vine work and a fossilized walrus tusk handle. At 16 1/2 inchces in length, Dean gave himself plenty of knife to decorate. (SharpByCoop image)
Legendary master smith and Hall of Famer Harvey Dean enjoys the historical aspect as well. “They’re just cool,” he offered. “A lot of people made them back years ago, and there was the idea of concealing them in the vest. Some were made with nickel-silver scabbards and called lapel knives because they were pinned under the vest or coat lapel.”
Dean’s pictured Tejas push dagger is a departure from standard sizing, with an overall length of 16¼ inches, with an 11-inch ladder pattern damascus blade and handle of fossilized walrus ivory. But then, everything is bigger in Texas.
“I’ve always liked [master smith] Larry Fuegen’s push daggers, and his work has had a lot of influence on mine,” Harvey said. “You really make them like any other knife, and I usually do around two or three a year. I like to use ivory and damascus and a stag handle is next up. I don’t do many plain ones, and most of mine are with two-piece handles. As far as marketing is concerned, you’ve got to have that special person who likes them–but they do usually sell quick.”
Hawks Nest Custom Push Talon
Matt Hunter (inset) has always had a thing for concealed carry knives, but admits his mother-of-pearl handled push daggers were his first crack at the style of knife. Angular and wickedly attractive, the Nichols Slither Armor Core stainless damascus daggers were designed as a matching set with his HawkWing knife, also pictured. (SharpByCoop image)
Damascus blade, mother-of-pearl handle and variations on the push dagger theme highlight Matt Hunter’s work at Hawks Nest Customs. He is a huge fan of concealed carry knives and started down the road with a boot dagger, neck knife and then his Push Talon.
“I think any dagger is challenging due to the symmetrical grinds that are required,” he noted. “You’ve really got to nail each and every one of them or the entire build needs to be scrapped. These push daggers are made with Nichols Slither Armor Core stainless damascus and mother-of-pearl on Westinghouse black canvas Micarta liners. “Believe it or not, these were my first push daggers,” Matt added. “These were originally made for a customer to match the HawkWing, which is also in this photo. I told him I was planning on doing a pair of matching push daggers, and he asked if we could do the mother of pearl to match his knife. So, I obliged.”
Zack Jonas Totem
A study in starkness, Zack Jonas’ Totem push dagger grabs the eye with its clean lines and depth of damascus. That’s a san mai steel with laddered W’s and faces in a 1,000-layer laminate with pure nickel. Adding to its Spartan charm are its gold handle accents. (SharpByCoop image)
The Zack Jonas push dagger featured is his Totem model with a blade length of 4 inches and an overall length of 6½ inches. Its gold handle accents complement a san mai steel with laddered W’s and faces in a 1,000-layer laminate with pure nickel.
“The push dagger is one of the few knives that is actually designed to be folded into a tightly closed fist,” the master smith explained. “That means you have to make sure the handle comfortably conforms to the shape of the human hand in that unusual position. A push dagger is not a particularly functional tool outside the very limited frame of hand-to-hand combat; if you don’t have a secure grip when you need it, you’ve got a real problem.
“There are few makers that come to mind as design influences,” Jonas concluded. “[Master smith] J.D. Smith’s early influence on my career is never far from my hand or eye. I also think of Peter Johnsson’s work as I’m designing. He has never done a push dagger that I’m aware of, but I like to try and channel the way he conducts tension through his lines. Peter and [master smith] Kevin Cashen both come to mind when I think of the functionality in any dagger.”
Andrew Meers Rose Of Sharon
A bold mix of materials, Andrew Meers utilizes carbon fiber, stainless steel, gold and a splintered mosaic damascus to bring-together this 9-inch push dagger. The centerpiece of the knife is its elegant Rose of Sharron engraving with the gold backing. (SharpByCoop image)
Andrew Meers included a push dagger in his ABS master smith set, which was complete with forged trout iron texture engraved with pangolins. “Push daggers have a place in my childhood memory,” he related. “I remember seeing one at a museum and being fascinated. In retrospect, I think having mostly seen conventionally handled pieces in media and collections, the manner in which the hand engages the handle is what is attractive to me.”
Meers’ featured push dagger is his first with a carbon fiber handle and a groove in the blade. Its 7-inch damascus blade is framed in stainless steel, and the engraving depicts the Rose of Sharon with a gold-plated relief background. The entire push dagger is 9 inches long. Andrew produced his first push dagger in 2014 and has made several since. His longest measured between 23 and 24 inches.
Jean Potvin Romanesque
Since push daggers are illegal in Jean Pierre Potvin’s homeland of Canada, he had to come up with a clever trick to get his his Romanesque push dagger past airport security and to a buyer at a show in Las Vegas. His solution, remove the illicit handle and replace it with a toilet plunger handle. (SharpbyCoop image)
“This push dagger is Roman in style,” remarked Jean Pierre Potvin. “It came about quite by chance. I rarely design in advance when I create. I prefer to let my imagination run free and follow new ideas that present themselves during the making process. During the making, I saw that it had a somewhat Roman style, and I continued in that direction with this result.”
Potvin’s push dagger measures 8 inches overall with a 4½-inch blade of damascus in 15N20 and 1084 carbon steel. The handle is fashioned from stabilized walnut burl and brass furniture. He had previously made only one push dagger. That was in 2022, and it was much smaller. “I had a buyer at the Nashville knife show,” he remembered, “and I had packed it in my luggage to take there. But when I got to the Montreal airport, it was confiscated by airport security.”
Since push daggers are illegal in Canada, that experience inspired Jean Pierre to remove the actual handle and replace it with a toilet plunger handle the next time he traveled with a push dagger. He made it to Las Vegas that second time and reattached the original handle after arrival. “It’s really funny because it’s the same dagger, but having a cross handle makes it illegal,” he smiled. “Sometimes you have to use tricks to get what you want.”
Somehow, the push dagger and its adventurous history seem to fit right in with Potvin’s novel experience.
Check Out More Cool Customs:
Cool Custom: Tony Lewis’ Tribute Knife To Steve Dunn
Cool Customs: Rocco Nawrocki’s Knife For Sergeant Bunker
First Case/Ruple collaboration officially debuts at BLADE Show ’24.
The combination of mechanical features, artistic design and choice of handle materials make the Bill Ruple x Case Axe Handle collaboration a unique knife for the user and collector.
Case Knives and BLADE Magazine Cutlery Hall-of-Fame® member Bill Ruple didn’t just bump into each other at the convenience store one day and say, “Hey, let’s do a knife collaboration.” That alone likely would have led to a great pocketknife, but no, there was a lot more planning and history that went into this new joint venture. We’ll talk about some of that but first let’s talk about the knife itself. It’s got some special character.
Case Axe Handle Design
Despite both being giants in the slipjoint field, Bill and Case sifted through some ideas and came up with a lockback pattern for an initial collaboration. It was not just one part but several features Bill combined together to make this knife unique.
Preeminent member of the Texas Slip Joint Cartel, Ruple more than understands what makes a good slippy.
As a man who had farmed the soil, he noted the end of the knife resembled the shape of an axe handle, thus the name. The upward curve of the handle butt provides some useful ergonomics but also strategically holds the tail of the lockbar. In this location, there is resistance to accidental unlocking of the blade while it’s in the open position. As well, it eliminates the need for a thumb cutout in the handle to release the blade. With an upward curve partially concealing the lockbar plus the absence of a thumb cutout, the handle makes the knife appear not to be a lockback pattern at all. In fact, since at first glance it seems to be a slipjoint, it has a bit of the trick-knife or mystery-lock character.
Initial prototyping by Bill in his shop hit a snag in that the slipjoint knives he’s used to creating have a rear bolster. That did not fit the artistic design for the new collaboration. However, Bill cleverly overcame the so-called snag by using a feature called a scissor spring (see illustration, page 40), which rests on a bushing to provide the needed tension to work the lockbar. Bill has prototyped knives for Case and also assisted with some aspects of manufacturing just as his Case collaboration predecessor, mentor, very close friend and fellow Cutlery Hall of Famer, Tony Bose, had done. Bill stated that nobody could replace Tony Bose and Case misses him. (Don’t be at all surprised if Case makes a commemorative knife in honor of Tony in the future.)
A few notes on Ruple’s design, the scissor spring (rear top right) is an efficient use of space with a one-piece unit of lockbar and spring. The bushing (lower fork of the spring), the spring rides on this avoiding excessive wear and taking up less room. It also acts as a rear spacer.
Both Case officials and Bill say Tony would be pleased with the new collaborative effort. The initial run will be 1,000 knives. Then the model will be made in a traditional slipjoint pattern. There is an aim at “near custom maker quality” for the first run, glibly naming the process “almost custom,” beginning with the parts being wire cut. That’s the cool way to say electrical discharge machining, or EDM. Production is assigned to a specific group of three workers only. No one else will work on the knives. That sort of consistency helps maintain quality control in manufacturing the knives.
MORE TO COME Is this collaboration just an outlier or will there be more Case/Ruple lockbacks in the future? Interest in the knife at BLADE Show 2024 (page 26), where the knife was officially introduced, was quite favorable. Both Bill and Case officials were pleased with how things have turned out, so expect to see another collaboration introduced at next year’s BLADE Show. That knife likely will be a slipjoint. Another lockback might be seen in the future, though a bit further down the road.
Natural birdseye maple is one of but several handle material options on the new Bill Ruple x Case Axe Handle.
As collaborative efforts go between manufacturer and custom maker, the Axe Handle knife is a superlative effort. And there is strong motivation to produce more collaborations, both commemorative and unique.
Ruple’s First Case
Does BLADE Magazine Cutlery Hall-of-Fame® member Bill Ruple remember his first Case knife? Is Texas big?
“Oh yeah,” the good-natured, award-winning knifemaker and South Texas Slipjoint Cartel trail boss said. “My dad gave me a Case knife when I was 9 or 10 years old, and it was a yellow handle Case trapper. And man, in about a month I had sharpened the blades completely out of that knife. And he gave me another one, and so he told me not to sharpen it quite as often. But yeah, a long time ago.”
Case Axe Handle Specs Knife type: Lockback Designer: BLADE Magazine Cutlery Hall-of-Fame® member Bill Ruple Blade length: 3.46” Blade material options: Wire-cut 154CM stainless steel or damascus Rockwell hardness: 57-59 HRC Blade grind: Flat taper Blade @ thickest: .126” Blade pattern: Clip point Blade finish: Satin Handle material options: Natural birdseye maple, Rogers jig chestnut bone, standard jig antique bone, marbled black carbon fiber, abalone, English walnut Lock: Lockback Opener: Nail nick Pocket clip: None Weight: 4.21 ozs. Closed length: 4.4” Carry: Suede leather taco pouch Special features: One-piece designed backspring & lock mechanism. Country of origin: USA MSRP: $599.99 to $774.99 Available: Late Summer 2024
From GiantMouse’s GM line, these new drops continue a storied tradition.
GiantMouse’s GM line has an impressive pedigree. Not only has it produced a BLADE Magazine’s Knife of the Year—the GMX—it has also proven among the company’s most popular collections.
One of the aspects adding to the line’s intrigue is the limited aspect of the knives that compose it. Early on, only 400 pieces were produced for each design—300 of the standard and 100 of the P version; now, it’s 600 total knives—400 standard and 200 of the P version. But in either amount, once the run is done, so is the design. So, if you like a knife from this line, you’ll need to be quick on the draw to procure one.
With that in mind, GiantMouse fans might need to limber up their left-mouse-click fingers, because the company has two new GMs about to drop—the GM14 and GMP14. These are the first additions to the collection in a spell and are sure to be popular when they go live on the GiantMouse website Dec. 9.
As the name suggests, the knives are very similar in design. The GMP offers some premium features. At the quick, what are collectors getting in the GM14 and GMP14? A slick, sleek and modern design. These knives are as comfortable in a three-piece suit as they would be in a pair of casual jeans.
The liner locks teeter on the larger side, with the blades measuring in at 3.6 inches and an overall length of 8.6 inches. Even with the size, the knives are featherweight, with the heavier of the two—the GMP—tipping the scales at less than 5 ounces. Much of the weight savings is thanks to titanium handles, which do a number on the knives’ overall mass.
GiantMouse uses Vanax steel for the blade, a nitrogen-alloy offering some pretty desirable traits. Among the most notable are its corrosion resistance, toughness and edge retention. You find this steel in a lot of high-end fishing knives or blades bound for moist environments.
Where the GM14 and GMP14 split paths is the bling GiantMouse incorporated into each design. In particular, the GMP features a darker PVD titanium handle, PVD Vanax blade and rich bronze inlays. An interesting aspect of the use of bronze is that it will patina over time, making each knife unique to its owner.
As for price, the GM14 rings up at $395, while the GMP14 has an MSRP of $445. Both look like solid additions to a storied line.
A bold new release from Benchmade, the Lowden blends premium materials, M390 steel, and fidget-worthy deployment in a sleek, spear-point EDC design.
Benchmade just shook things up with the release of the Lowden—and if you’re into flippers, this one’s going to catch your eye.
Known for their rock-solid AXIS lock and high-quality builds, Benchmade isn’t typically the first brand you think of when it comes to rear flippers. But the Lowden changes that.
This sleek little blade flips open like a dream. You’ve got the option of using the flipper tab or sticking with the tried-and-true AXIS lock for one-handed deployment, and both are smooth and snappy. It’s a fun, fidget-friendly knife that doesn’t compromise on function.
The Lowden sports a 2.79-inch spear-point blade made from M390 super steel—translation: this thing holds an edge like a champ, resists corrosion, and is tough enough for serious work.
The handles are lightweight anodized aluminum with a stainless-steel inset frame, giving it that slim, dagger-inspired profile without skimping on strength. Plus, Benchmade matched the color on the AXIS button and deep-carry pocket clip for a clean, cohesive look.
Sure, a spear-point blade might seem like an odd choice for EDC or outdoor use, but in practice, it works. It’s surprisingly versatile, with great piercing power and slicing ability. The ergonomics are solid too—with an ample handle fitting comfortably in a wide range of hand sizes and offers a confident grip.
Are there a couple of nitpicks? Sure.
There’s no lanyard hole, which could be a downside for folks who like a little extra security, and the flipper tab could use some jimping. But overall, the Lowden is a refined, premium knife that’s just plain enjoyable to carry and use—classic Benchmade quality with a fresh twist.
